制動器外文翻譯 制動器

《制動器外文翻譯 制動器》由會員分享，可在線閱讀，更多相關《制動器外文翻譯 制動器（13頁珍藏版）》請?jiān)谘b配圖網上搜索。

1、 本科生畢業設計（論文）外文翻譯 畢業設計（論文）題目：幾種典型的制動器的對比分析與設計 外文題目：THE BRAKE BIBLE 譯文題目：制動器 學 生 姓 名： 專 業： 車輛工程 指導教師姓名： 評 閱 日 期： THE BRAKE BIBLE Brakes - what do they do

2、? The simple answer: they slow you down. The complex answer: brakes are designed to slow down your vehicle but probably not by the means that you think. The common misconception is that brakes squeeze against a drum or disc, and the pressure of the squeezing action is what slows you down. This in

3、fact is only part of the equation. Brakes are essentially a mechanism to change energy types. When youre travelling at speed, your vehicle has kinetic energy. When you apply the brakes, the pads or shoes that press against the brake drum or rotor convert that energy into thermal energy via friction.

4、 The cooling of the brakes dissipates the heat and the vehicle slows down. Its the First Law of Thermodynamics, sometimes known as the law of conservation of energy. This states that energy cannot be created nor destroyed, it can only be converted from one form to another. In the case of brakes, it

5、is converted from kinetic energy to thermal energy. Angular force. Because of the configuration of the brake pads and rotor in a disc brake, the location of the point of contact where the friction is generated also provides a mechanical moment to resist the turning motion of the rotor. Thermodyna

6、mics, brake fade and drilled rotors. If you ride a motorbike or drive a race car, youre probably familiar with the term brake fade, used to describe what happens to brakes when they get too hot. A good example is coming down a mountain pass using your brakes rather than your engine to slow you do

7、wn. As you start to come down the pass, the brakes on your vehicle heat up, slowing you down. But if you keep using them, the rotors or drums stay hot and get no chance to cool off. At some point they cant absorb any more heat so the brake pads heat up instead. In every brake pad there is the fricti

8、on material that is held together with some sort of resin and once this starts to get too hot, the resin starts to vapourise, forming a gas. Because the gas cant stay between the pad and the rotor, it forms a thin layer between the two whilst trying to escape. The pads lose contact with the rotor, r

9、educing the amount of friction and voila. Complete brake fade. The typical remedy for this would be to get the vehicle to a stop and wait for a few minutes. As the brake components cool down, their ability to absorb heat returns and the next time you use the brakes, they seem to work just fine. Thi

10、s type of brake fade was more common in older vehicles. Newer vehicles tend to have less outgassing from the brake pad compounds but they still suffer brake fade. So why? Its still to do with the pads getting too hot. With newer brake pad compounds, the pads transfer heat into the calipers once the

11、rotors are too hot, and the brake fluid starts to boil forming bubbles in it. Because air is compressible (brake fluid isnt) when you step on the brakes, the air bubbles compress instead of the fluid transferring the motion to the brake calipers. Voila. Modern brake fade. So how do the engineers

12、design brakes to reduce or eliminate brake fade? For older vehicles, you give that vapourised gas somewhere to go. For newer vehicles, you find some way to cool the rotors off more effectively. Either way you end up with cross-drilled or grooved brake rotors. While grooving the surface may reduce th

13、e specific heat capacity of the rotor, its effect is negligible in the grand scheme of things. However, under heavy braking once everything is hot and the resin is vapourising, the grooves give the gas somewhere to go, so the pad can continue to contact the rotor, allowing you to stop. The whole

14、understanding of the conversion of energy is critical in understanding how and why brakes do what they do, and why they are designed the way they are. If youve ever watched Formula 1 racing, youll see the front wheels have huge scoops inside the wheel pointing to the front (see the picture above). T

15、his is to duct air to the brake components to help them cool off because in F1 racing, the brakes are used viciously every few seconds and spend a lot of their time trying to stay hot. Without some form of cooling assistance, the brakes would be fine for the first few corners but then would fade and

16、 become near useless by half way around the track. Rotor technology. If a brake rotor was a single cast chunk of steel, it would have terrible heat dissipation properties and leave nowhere for the vapourised gas to go. Because of this, brake rotors are typically modified with all manner of extra

17、design features to help them cool down as quickly as possible as well as dissapate any gas from between the pads and rotors. The diagram here shows some examples of rotor types with the various modification that can be done to them to help them create more friction, disperse more heat more quickly,

18、and ventilate gas. From left to right. 1: Basic brake rotor. 2: Grooved rotor - the grooves give more bite and thus more friction as they pass between the brake pads They also allow gas to vent from between the pads and the rotor. 3: Grooved, drilled rotor - the drilled holes again give more bit

19、e, but also allow air currents (eddies) to blow through the brake disc to assist cooling and ventilating gas. 4: Dual ventilated rotors - same as before but now with two rotors instead of one, and with vanes in between them to generate a vortex which will cool the rotors even further whilst trying t

20、o actually suck any gas away from the pads. An important note about drilled rotors: Drilled rotors are typically only found (and to be used on) race cars. The drilling weakens the rotors and typically results in microfractures to the rotor. On race cars this isnt a problem - the brakes are changed

21、after each race or weekend. But on a road car, this can eventually lead to brake rotor failure - not what you want. I only mention this because of a lot of performance suppliers will supply you with drilled rotors for street cars without mentioning this little fact. Big rotors. How does all this

22、apply to bigger brake rotors - a common sports car upgrade? Sports cars and race bikes typically have much bigger discs or rotors than your average family car. A bigger rotor has more material in it so it can absorb more heat. More material also means a larger surface area for the pads to generate f

23、riction with, and better heat dissipation. Larger rotors also put the point of contact with the pads further away from the axle of rotation. This provides a larger mechanical advantage to resist the turning of the rotor itself. To best illustrate how this works, imagine a spinning steel disc on an a

24、xle in front of you. If you clamped your thumbs either side of the disc close to the middle, your thumbs would heat up very quickly and youd need to push pretty hard to generate the friction required to slow the disc down. Now imagine doing the same thing but clamping your thumbs together close to t

25、he outer rim of the disc. The disc will stop spinning much more quickly and your thumbs wont get as hot. That, in a nutshell explains the whole principle behind why bigger rotors = better stopping power. The different types of brake. All brakes work by friction. Friction causes heat which is part

26、of the kinetic energy conversion process. How they create friction is down to the various designs. Bicycle wheel brakes I thought Id cover these because theyre about the most basic type of functioning brake that you can see, watch working, and understand. The construction is very simple and out

27、-in-the-open. A pair of rubber blocks are attached to a pair of calipers which are pivoted on the frame. When you pull the brake cable, the pads are pressed against the side or inner edge of the bicycle wheel rim. The rubber creates friction, which creates heat, which is the transfer of kinetic ener

28、gy that slows you down. Theres only really two types of bicycle brake - those on which each brake shoe shares the same pivot point, and those with two pivot points. If you can look at a bicycle brake and not understand whats going on, the rest of this page is going to cause you a bit of a headache.

29、 Drum brakes - single leading edge The next, more complicated type of brake is a drum brake. The concept here is simple. Two semicircular brake shoes sit inside a spinning drum which is attached to the wheel. When you apply the brakes, the shoes are expanded outwards to press against the insid

30、e of the drum. This creates friction, which creates heat, which transfers kinetic energy, which slows you down. The example below shows a simple model. The actuator in this case is the blue elliptical object. As that is twisted, it forces against the brake shoes and in turn forces them to expand out

31、wards. The return spring is what pulls the shoes back away from the surface of the brake drum when the brakes are released. See the later section for more information on actuator types. The "single leading edge" refers to the number of parts of the brake shoe which actually contact the spinning

32、drum. Because the brake shoe pivots at one end, simple geometry means that the entire brake pad cannot contact the brake drum. The leading edge is the term given to the part of the brake pad which does contact the drum, and in the case of a single leading edge system, its the part of the pad closest

33、 to the actuator. This diagram (right) shows what happens as the brakes are applied. The shoes are pressed outwards and the part of the brake pad which first contacts the drum is the leading edge. The action of the drum spinning actually helps to draw the brake pad outwards because of friction, whic

34、h causes the brakes to "bite". The trailing edge of the brake shoe makes virtually no contact with the drum at all. This simple geometry explains why its really difficult to stop a vehicle rolling backwards if its equipped only with single leading edge drum brakes. As the drum spins backwards, the l

35、eading edge of the shoe becomes the trailing edge and thus doesnt bite. Drum brakes - double leading edge The drawbacks of the single leading edge style of drum brake can be eliminated by adding a second return spring and turning the pivot point into a second actuator. Now when the brakes are a

36、pplied, the shoes are pressed outwards at two points. So each brake pad now has one leading and one trailing edge. Because there are two brake shoes, there are two brake pads, which means there are two leading edges. Hence the name double leading edge. Disc brakes Some background. Disc brakes

37、 were invented in 1902 and patented by Birmingham car maker Frederick William Lanchester. His original design had two discs which pressed against each other to generate friction and slow his car down. It wasnt until 1949 that disc brakes appeared on a production car though. The obscure American car

38、builder Crosley made a vehicle called the Hotshot which used the more familiar brake rotor and calipers that we all know and love today. His original design was a bit crap though - the brakes lasted less than a year each. Finally in 1954 Citron launched the way-ahead-of-its-time DS which had the fir

39、st modern incarnation of disc brakes along with other nifty stuff like self-levelling suspension, semi-automatic gearbox, active headlights and composite body panels. (all things which were re-introduced as "new" by car makers in the 90s). Disc brakes are an order of magnitude better at stopping v

40、ehicles than drum brakes, which is why youll find disc brakes on the front of almost every car and motorbike built today. Sportier vehicles with higher speeds need better brakes to slow them down, so youll likely see disc brakes on the rear of those too.

41、制動器 制動器：它們的作用？ 簡單的說：它會使你的汽車慢下來。 復雜的說：制動器被用來讓你的車減速，但可能不是你所想的意思。普遍的誤解是，制動器擠壓制動鼓或制動片，擠壓的壓力的作用使你的車慢下來。但這只是制動的一部分。制動系統本質上是改變能量的類型。當你在全速行駛時，你的汽車獲得動能。當你踩下剎車，墊子或鞋子對制動鼓和轉子的作用轉化為摩擦熱能。剎車的冷卻使車的熱能消散，減慢車速。這是熱力學第一定律，有時被視為能量守恒定律。也是就說：能量不能被創造也不能被消滅，只能由一種形式轉換成另一種。制動情況下，它是動能轉化為熱能。 角向力。 因?yàn)樵诒P(pán)式制動器的剎車片和轉子的位置，摩擦產生的接觸點的

42、位置也產生了一個機械的抵御轉子的回轉運動。 The cooling of the brakes dissipates the heat and the vehicle slows down熱力學，制動失效，鉆孔轉子。 如果你騎摩托車或駕駛一輛賽車，你或許熟悉制動失效，描述當制動器太熱，他發生了什么。一個很好的例子就是從山上下來使用剎車制動,而不是你的引擎使你減速。當汽車開始滑動下來時，剎車使汽車產生熱能,使你減速。但是如果你持續使用他們， 轉子或鼓留熱并沒有機會冷卻。從某種意義上說他們不能吸收更多的熱量，使剎車墊熱了起來。在每一個墊子的摩擦材料有某種共同的樹脂一旦開始變得太熱，該樹脂開始蒸

43、發，形成氣。由于氣體之間不能待在墊層及轉子，而是形成薄薄的一層在兩個之間準備排走。墊失去與轉子的接觸，減少摩擦和熱量。這是完全的制動失效。 典型的補救辦法，將車停了下來，等待幾分鐘。由于制動部件降溫，吸收熱量的原因，下一次您使用剎車的能力，似乎會好一點。這種類型的制動失效在舊車輛更常見。新的車輛往往從剎車墊中減少排氣，但他們?nèi)杂兄苿?dòng)失效。為什么呢？它仍然因?yàn)閯x車墊太熱。猶由于新的剎車墊合成，襯墊的熱傳遞到卡鉗一旦轉子太熱了，制動液開始沸騰冒泡。因?yàn)榭諝馐强蓧嚎s的(制動液不是)當你踩剎車，氣泡的壓縮代替了流體轉移到制動卡鉗。這就是現代制動失效。 工程師們是怎樣設計減少或消除剎車制動失效的?

44、年長的車輛，是使氣化的氣體有地方排掉。新的車輛，找到一些方式來冷卻轉子更為有效。無論如何你最終獲得交叉鉆孔或溝槽剎車盤。當槽表面是可以減少比熱容量的轉子，其效果可以忽略不計的。然而當大力剎車時一旦一切都是熱和樹脂材料蒸發，槽讓氣體排去， 所以墊可以繼續接觸轉子，讓車減速停下來。 整個的理解能量轉換的關鍵是，剎車他們?cè)撟鍪裁?以及為什么它們?cè)O(shè)計成這樣。如果你曾看過一級方程式賽車，你就可以看到向前的前輪里面有很大的洞（如上圖所示）。這是管道空氣剎車部件，以幫助他們冷卻下來，因?yàn)樵贔1賽車中，剎車每隔幾秒鐘頻繁使用，花很多時間預留熱量。如果沒有某種冷卻協助，剎車就可能在最開始的幾個轉角失靈，最后剎

45、車失效賽車在一半路程出局。 轉子技術。 如果制動轉子是一個單一的鋼鐵鑄塊，這將有嚴重的散熱性能和氣化氣無法排去。因此，剎車盤通常使用各種額外的設計特點的方式來改進幫助他們冷卻下來，盡快使墊和轉子之間的任何氣體排走。 The diagram here shows some examples of rotor types with the various modification that can be done to them to help them create more friction, disperse more heat more quickly, and ventilate g

46、as.這里的圖表顯示了轉子類型的各種修改，可以改進幫助他們創造更多的摩擦力，更迅速地驅散更多的熱量，通風氣體的一些例子。 From left to right.從左至右。 1：基本制動轉子。2：溝槽轉子-溝槽給予更多口，他們之間產生更多的摩擦，還允許氣體從墊和轉子之間的排走。3：溝槽鉆孔轉子-再給多一點口，但也讓氣流(渦旋)通過制動盤協助冷卻和通風。4：雙通風轉子-以前一樣，然而現在有了兩個轉子而不是一個，和他們之間葉片產生渦流將進一步冷卻轉子同時試圖實際上從襯墊中排掉任何氣體。 重要的一點：鉆孔轉子通常只使用于賽車。鉆孔使得轉子變?nèi)?，通常?huì)導致轉子產生各類裂縫。在賽車中這不是一個問題——

47、在每場比賽或者每周都會更換剎車盤。但在路上的車，最終會導致剎車轉子失靈的，不是你能想象的。我只提這件事，因?yàn)橛性S多供應商將為您提供鉆孔轉子，沒有直接提到這個事實。 大轉子。 這是如何適用于更大的剎車轉子-一種普遍的跑車升級？汽車和自行車運動比賽通常有比一般的家庭汽車更大的盤或轉子。一個更大的轉子有更多的材料在里面，因此它可以吸收更多的熱量。更多的物質也意味著更大的表面積，墊片產生摩擦,和更好的散熱。較大的角度也將轉子接觸墊進一步遠離軸旋轉。這提供了一個更大的機械優勢抵抗旋轉的轉子本身。這個工作最好的說明，設想一種紡紗鋼軸上的閥瓣在你的面前。如果你夾緊你的大拇指任何一方的閥瓣靠近中間，你的大

48、拇指將熱得非常快，你會需要推動相當大的摩擦力使閥瓣慢下來。現在想象做同樣的事情，但是你的大拇指夾在一起接近外緣的閥瓣。閥瓣將停止旋轉得特別快，你的大拇指也不會很熱。簡單地說解釋整個原理就是更大轉子=更好的制動原則。 不同類型的制動器。 所有制動器都產生摩擦力。摩擦力是熱的一部分動能轉換過程。他們是如何不同的設計產生了摩擦的。 自行車車輪制動器 我想我覆蓋這些，因?yàn)樗鼈兪亲罨绢?lèi)型的制動方式，你可以看到，看工作了解。設計非常簡單，在外部。一雙橡膠塊連接到一雙卡鉗，能在機架上旋轉。When you pull the brake cable, the pads are pressed aga

49、inst the side or inner edge of the bicycle wheel rim.當你拉剎車線，剎車墊壓向一側或自行車輪輞的內側邊緣。 The rubber creates friction, which creates heat, which is the transfer of kinetic energy that slows you down.橡膠產生摩擦，產生熱量，這是動能轉移使車慢下來。 自行車制動實際上Theres only really two types of bicycle brake - those on which each brake shoe

50、 shares the same pivot point, and those with two pivot points.只有兩個類型 - 自行車剎車制動蹄上有相同的摩擦點，并有兩個摩擦點。 If you can look at a bicycle brake and not understand whats going on, the rest of this page is going to cause you a bit of a headache.如果你可以看了自行車制動，不明白發生了什么事情，本頁面的其余部分你理解起來有麻煩了。 鼓式制動器-單前沿 下一個，更加復雜的類型的制

51、動是鼓式制動器。這是簡單的概念。兩個半圓形的剎車片裝在里面連接一個旋轉的車輪的鼓。當你踩下剎車,剎車片向外擴大擠壓內側的鼓。這造成了摩擦，產生熱量，轉移動能，這將使車減速。下面的例子顯示了一個簡單的模型。制動器在這種情況下是藍色橢圓形的對象。因?yàn)檫@是扭曲的，它的力使剎車片迫使他們向外擴張。當松開剎車，The return spring is what pulls the shoes back away from the surface of the brake drum when the brakes are released.回位彈簧從制動鼓的表面拉回剎車片?？吹秸鹿?jié)后面更多信息。 "單前

52、沿"是指實際接觸的旋轉鼓輪制動蹄部件的數量。因?yàn)橹苿?dòng)蹄片在一端，簡單的幾何意味著整個剎車片無法都接觸到制動鼓。單前沿就是部分剎車片的術語，那些接觸制動鼓，在單一制動情況下的方法，在最接近制動器的襯墊。此圖 （右側） 顯示當剎車時，會發生什么情況。這剎車片向外壓和制動襯墊的最初接觸制動鼓的部分剎車片就是前沿。制動鼓旋轉實際上有助于制動片向外加壓，因?yàn)閯x車片向口子的摩擦力。后沿的制動蹄片與制動鼓幾乎沒有接觸。這個簡單的幾何解釋了，為什么汽車是很難停止向后滾動，如果它只配單前緣沿鼓式制動器。由于制動鼓向后旋轉，前沿的剎車片成為了后沿，因?yàn)橹苿?dòng)不會咬合。 鼓剎車-雙前沿 可以通過添加回位彈簧和旋轉

53、第二個制動器中心點來消除鼓式制動器的單個前沿的缺點。踩下剎車時，剎車片在兩個點向外壓。所以每個剎車片現在有一個前沿的和一個后沿。因?yàn)橛袃蓚€(gè)剎車蹄，那里有兩個剎車片，這意味著有兩個邊沿。因此名稱雙前沿。 盤式制動器一些背景。 盤式制動器在 1902 年被發明，伯明翰汽車制造商檢基威廉 蘭徹斯特的專利。他原先的設計了兩個光盤，緊貼彼此產生摩擦來使車減速。直到 1949 盤式制動器的量產車上使用。在美國汽車創始人克羅斯利發明了我們目前熟知和喜愛的快車，就是使用了很多類似的盤動制動器和卡鉗。他原先的設計雖然有點缺陷-制動器持續不到一年。終于在 1954 年雪鐵龍推出先進的DS，成就了像自流平懸浮、 半自動變速箱、 活動前燈和復合車身盤式制動器的第一次現代化身。（所有事情，在 90 年代的汽車制造商都重新作為"新型"）。 盤式制動器比鼓式制動器好了一個數量級來使車輛制動，這就是為什么你會發現的現代幾乎所以汽車和摩托車都使用的是盤式制動器。運動型車輛具有更高的速度需要更好的制動減速，所以您會明白盤式制動器在這些車上的使用。