購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
河南機電高等?？茖W(xué)校畢業設計說明書
線圈骨架注塑成型工藝及模具設計
摘要：本設計題目為線圈骨架塑料成型工藝及模具設計，體現了板類塑料零件的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者注塑模設計的基礎知識，為設計更復雜的注塑模具做好了鋪墊和吸取了更深刻的經驗。
本設計運用塑料成型工藝及模具設計的基礎知識，首先分析了塑件的成分及性能要求，為選取澆口的類型做好了準備；然后估算了塑件的體積，便于選取注塑機及確定型腔數量；最后分析了塑件的特征，確定模具的設計參數、設計要點及推出裝置的選取。
根據本塑件結構，塑件很薄，為了使其在推出的時候不變形，必須采用推桿推出機構。這種推出機構非常適合在本副模具中使用。
關鍵詞：注塑模 流道 推出機構 型腔
Coil skeleton injection molding craft and mold design
Abstract:The topic of design for the designing of injection molding of coil skeleton, reflects the type of plastic parts of the shell design, content and direction of a certain design significance. Parts of the mold through the design, the designer has been further strengthened by the injection mold design based on knowledge, for the design of more complex injection molds made and lessons foreshadowing a more profound experience.
The designing of the use of injection molding and die designing of the basic knowledge, the first analysis of the plastic parts of the composition and performance requirements, select the type of gate prepared for the then estimate the volume of plastic parts, injection molding machines and facilitate the selection of identified Cavity volume of the final pieces of plastic the characteristics of the design parameters established mold, design elements and the introduction of the device selected.
According to this models a structure, models to be very thin, to cause it in promotes time does not distort, must use the throwout lever ejecting mechanism. This kind of ejecting mechanism is suitable in this mold to use.
Keywords: Injection moulding , Runner, Ejecting mechanism
, Cavity