壓縮包已打包上傳。下載文件后為完整一套設計?!厩逦?,無水印,可編輯】dwg后綴為cad圖紙,doc后綴為word格式,所見即所得。有疑問可以咨詢QQ 197216396 或 11970985
目 錄
摘要…………………………....………………….……………………...Ⅰ
ABSTRACT.....................................................................................................Ⅱ
1 緒論..........................................................................................................3
2 撥叉C的分析.............................................................................................4
2.1撥叉C的作用...........................................................................................4
2.2撥叉C的工藝分析.....................................................................................4
2.3撥叉C的工藝要求.....................................................................................4
2.4毛坯的選擇..............................................................................................5
2.5 本章總結................................................................................................5
3 工藝規程設計.............................................................................................6
3.1加工工藝過程...........................................................................................6
3.2確定各表面加工方案..................................................................................6
3.2.1選擇加工方法時,需考慮的因素.............................................................6
3.2.2面的加工...........................................................................................6
3.2.3孔的加工...........................................................................................7
3.2.4槽的加工...........................................................................................7
3.3確定定位基準...........................................................................................7
3.3.1粗基準的選擇.....................................................................................7
3.3.2精基準選擇的原則...............................................................................8
3.4工藝路線的擬訂........................................................................................8
3.4.1工序的合理組合..................................................................................8
3.4.2工序的集中與分散...............................................................................9
3.4.3加工階段的劃分................................................................................10
3.4.4加工工藝路線方案的比較....................................................................11
3.5撥叉C的偏差,加工余量,工序尺寸及毛坯尺寸的確定.......................................12
3.5.1毛坯的結構工藝要求..........................................................................12
3.5.2撥叉C的偏差計算.............................................................................13
3.6確定切削用量及基本工時(機動時間)..........................................................14
3.7時間定額計算及生產安排..........................................................................22
3.7.1鉆預制孔.........................................................................................22
3.7.2鉆預制孔.........................................................................................23
3.7.3拉25H7內花鍵................................................................................23
3.7.4粗、精銑18H11底槽........................................................................................23
3.7.5粗、精銑上端面...............................................................................................24
3.7.6鉆、攻2-M8螺紋孔.........................................................................................25
3.8 本章總結..............................................................................................................26
4 專用夾具設計..........................................................................................................27
4.1夾具設計概述........................................................................................................27
4.2鉆、攻2—M8螺紋孔夾具設計..................................................................................30
4.2.1研究原始質料.................................................................................................30
4.2.2定位基準的選擇..............................................................................................30
4.2.3夾具方案的設計選擇.......................................................................................30
4.2.4切削力及夾緊力的計算...................................................................................30
4.2.5誤差分析與計算..............................................................................................31
4.2.6夾具設計及操作的簡要說明............................................................................32
4.3 本章總結..............................................................................................................32
結論..........................................................................................................................43
參考文獻......................................................................................................................44
致 謝............................................................................................................................45
3