購買設計請充值后下載,,資源目錄下的文件所見即所得,都可以點開預覽,,資料完整,充值下載就能得到。。?!咀ⅰ浚篸wg后綴為CAD圖,doc,docx為WORD文檔,有不明白之處,可咨詢Q:1304139763
摘要
本文主要研究了四輪轉向傳動系統的基本結構和工作原理,并對四輪轉向傳動路線進行了簡要分析。以此為理論基礎,以某汽車的相關參數設計了四輪轉向轉向器。包括前輪轉向器的設計計算,后輪轉向執行器的設計,齒條等強度的計算。四輪轉向傳動系主要是通過車速傳感器、前輪轉角傳感器、前輪轉速傳感器、方向盤轉角傳感器、后輪轉角傳感器、后輪轉速傳感器,發送信號到四輪轉向控制器內,信號經過處理,得出后輪所需的轉角大小及方向,控制執行器完成轉向。此系統可以改善車輛低速的轉向靈活性和高速時的操縱穩定性,使汽車在轉向時響應快,轉向能力強,直線行駛穩定。前輪轉向器是四輪轉向的基礎部件,是電機助力的齒輪齒條轉向器。后輪執行器是驅動后輪轉向的主要部件。通過對前輪轉向器和后輪執行器的設計,為四輪轉向技術整體設計提供了基礎。
關鍵詞 四輪轉向,齒輪齒條電動助力轉向器,后輪轉向執行器
Abstract
This paper mainly studies is the four-wheel steering transmission system the basic structure and working principle, and the four-wheel steering transmission routes are briefly analyzed. This theory, with a car related parameters of the four-wheel steering transmission system was designed. Including front wheel steering gear design calculation, rear wheel actuator design strength calculation, rack .Four-wheel steering transmission system is primarily through speed sensor, front wheel Angle sensor, front wheel speed sensor, steering wheel Angle sensor, rear Angle sensor, rear Lord Angle sensor, rear vice, rotational speed sensor sends a signal to the four-wheel steering controller inside, signal through processing, draw the rear required corner size and direction, control actuator finish turning. This system can improve vehicle speed steering flexibility and high speed control stability of, make cars in steering response quickly, steering capability is strong, run straight stability. Front wheel steering gear is the basic components, four-wheel steering motor hydraulically rack-and pinion steering gear Rear actuators are drive rear wheel steering the major components. Through the front wheel steering gear and rear actuator is designed for four-wheel steering technology integral design provides the basis.
Key words Four-wheel steering gear rack of electric power steering gear, rear wheel actuators
目錄
摘要 I
Abstract II
目錄 III
第一章 緒論 1
第二章 設計方案選擇 7
2.1 各傳感器位置確定 7
2.2 轉向機構的設計要求 8
2.3 轉向梯形設計 9
2.4 本章小結 10
第三章 齒輪齒條電動助力轉向器設計計算 11
3.1 轉向器的效率 11
3.2 轉向器正效率η+ 11
3.3 轉向器逆效率η- 12
3.4 傳動比的變化特性 13
3.4.1力傳動比與角傳動比的關系 14
3.5 參數選擇 16
3.5.1轉向輪側偏角計算 17
3.6 轉向系載荷確定 18
3.7 轉向器的主要元件設計 19
3.7.1選擇齒輪齒條材料 19
3.7.2齒輪齒條基本參數 21
3.7.3轉向橫拉桿及其端部 22
3.7.4齒條調整 23
3.8 齒輪齒條轉向器轉向橫拉桿的運動分析 24
3.9 齒輪齒條傳動受力分析 25
3.10 彈簧的設計計算 29
3.11 齒輪軸軸承的校核 32
3.12 電機選擇 33
3.12.1助力轉矩的計算 33
3.12.2電動機參數的選擇和計算 34
3.13 本章小結 34
第四章 后輪轉向執行器設計計算 35
4.1 執行器結構設計 35
4.2 齒條設計計算 35
4.3 回位彈簧的設計計算 35
4.4 電機選擇 37
4.4.1助力轉矩的計算 37
4.4.2電動機參數的選擇和計算 37
4.5 本章小結 37
結論 39
致謝 40
參考文獻 41
附錄 42
- 4 -