目 錄
摘 要··································································Ⅲ
ABSTRACT····························································Ⅳ
1 前 言
1.1 選題背景·····························································1
1.2課題設計思路·························································1
1.3設計過程中的難點·····················································2
2 工藝分析及計算
2.1工件的基本信息分析···················································3
2.2工藝分析·····························································3
2.2.1工序計算 ·························································4
2.2.2計算毛坯直徑······················································5
2.2.3工藝方案的確定·····················································7
2.2.4排樣及搭邊·························································8
2.3工藝計算·····························································9
2.3.1工藝力的計算及壓力機的選擇········································9
2.3.2主要工作部分尺寸計算··············································12
3模具設計
3.1落料拉深復合模的設計················································15
3.1.1落料拉深復合模結構設計············································15
3.1.2落料拉深復合模主要零件設計········································16
3.2沖孔模設計··························································19
3.2.1沖孔模結構設計····················································19
3.2.2沖孔模主要零件設計················································20
3.3翻邊模設計··························································22
3.3.1翻邊模結構設計····················································22
3.3.2翻邊模主要零件設計················································22
3.4切邊整形復合模的設計················································24
3.4.1切邊整形復合模結構設計············································24
3.4.2切邊整形復合模主要零件設計········································25
3.5擴口壓平復合模的設計················································27
3.5.1擴口壓平復合模結構設計············································27
3.5.2擴口壓平復合模主要零件設計········································27
4 結 論································································31
謝 辭··································································32
參考文獻·······························································33
IV
摘 要
本文是對拉深件進行工藝分析及模具設計。該工件是一個圓筒形拉深件，另外該工件的底部帶有通孔，需進行沖孔翻邊，雖然形狀不太復雜但肯定不能一次成形。通過對零件各部分進行計算分析后才能最終確定加工工序。工件整個成形過程所涉及的工序有：落料、拉深、沖孔、翻邊等四步。通過計算分析得翻邊能一次成形，所以不需進行預拉深，而計算可知拉深可一次成形，所以確定最終工藝方案為：落料與拉深復合，沖孔、翻邊復合。在確定工藝方案的基礎上對主要模具進行設計，分析工件成型過程，設計模具的結構并畫出模具裝配圖及零件圖。在本次設計中主要對落料拉深復合模以及沖孔、翻邊模進行設計。
關鍵詞：拉深；落料拉深復合模；
ABSTRACT
The thesis is focus on the process analysis and mold design of the drawing.The workpiece we design is a cylinder-shaped drawing parts,which has a hole at the bottom.The workpiece should be punched and flanged.Although the shape is not very complex,it couldn’t be shaped by one step.We can determine the processing by analyzing the parts of the workpiece.The process include several steps:blanking,drawing,punching and flanging.By analysis,we know that the flanging can be finished by one step.There should not be a pre-drawing.However,the drawing can be achieved easily.Therefore,the final process is compounding the blanking with the drawing, the punching die and flanging die.Besides,we should design the main die,analyse the process,design the structure of the die and draw the assembly and workpiece picutures.In this graduation project,we mainly design the blanking drawing die, the punching die and flanging die.
Key words: drawing die； blanking drawing compound die；
- 1 -